Showing posts with label mash. Show all posts
Showing posts with label mash. Show all posts

Saturday, July 5, 2014

Effect of mash pH on flavor profile

Importance of mash pH

In a previous article on the mash, I mentioned that high pH can have adverse effects on the beer. Here is a write up of an experiment that tries to qualify the difference between two beers with different mash pH's.

What does a high pH do to my beer?

pH is a measure of the concentration of hydrogen ions in a solution. In explicit terms, the pH is -log[H+], where [H+] is the concentration of hydrogen ions in moles/L. A consequence of the -log function is that as the concentration of the hydrogen ion increases, the pH goes down. The most common range of pH is between 0-14, but it can be higher or lower and even a negative number (though a pH outside that range is very rare outside of a lab).

pH affects your beer in two ways. First, each enzyme in the mash has an optimal range of function in terms of temperature and pH. The enzymes responsible for converting the starches to sugars function most efficiently between a pH of 5.3 and 5.8. As the pH during the saccrification rest increases above 6.0, the enzymes will yield a wort that is less attenuative.

The pH also affects the flavor of the beer. The husks of the grain are full of tannins that can be extracted during the mash and sparge. The reaction pathway of how these chemicals dissolve into the beer is simple. The tannins are a weak acid and, like all acids, have a tendency to donate a hydrogen ion into solution. However being a weak acid, this donation only occurs when the concentration of hydrogen ions is relatively low (as is the case when the pH is too high).

If the concentration of hydrogen ions in solution is low enough, a hydrogen ion will dissociate from the tannin, leaving behind a negatively charged molecule. This negatively charged molecule can more easily dissolve into solution due to water's polar nature. This is why it is important to keep the pH in check: the free hydrogen ions will prevent the tannins from dissolving into the solution.

Most online sources give a pH threshold of 5.8 to 6.0 to prevent tannin extraction. This experiment was conducted to determine qualitatively where the tannin extraction starts in terms of pH.

Experimental Design

Two batches of beer were brewed identically except the water of one was not treated with phosphoric acid to reduce the pH. The two batches of beers are identified as B#160 and B#171. The mash pH of B#160 was 6.0, while the mash pH of B#171 was 5.8. Again, the aim of this experiment was to show how small changes in the mash pH can result in a completely different beer.

A survey was completed with nine participates to rate different aspects of the beer on a scale of 0-6, with 0 being not present and 6 being overpowering. The aspects are Aroma, Carbonation, Body, Hop Character, Fruity/Estery, Malty/Grainy, Roasted, Caramel, Aftertaste, Bitterness, Diacetyl, and Astringency. In addition to these specific categories, each participate rated their overall impression of the beer on a scale from -4 to +4; -4 is awful, 0 is average, and +4 is awesome. The ratings for each category were averaged and used to develop some sort of description of the beer.

Results
Table 1 - Batch parameters

There were some differences between the two beers other than the mash pH, which are tabulated in table 1. The "Final Runnings" is the last portion of the liquid that is run off from the lauter and into the boil kettle. The pH of this will be close to the mash pH at the beginning of the run off and will climb to neutral as the grain is sparged. The gravities are reported in degrees Plato. Ideally, the gravity of the final runnings should not drop below 3.0degP, and the pH should not be above 6.

The differences between the brews that led to interesting results in the surveys are the starting and final gravities. B#160 had a slightly higher starting gravity and a much higher final gravity. This is reflected in the lower % Attenuation, and can be interpreted as B#160 having more residual sugars. Both batches had accurate pitch rates, and were fermented with a low generation of yeast.

Survey Results

Table 2 - Survey Results
Table 2 shows the survey results in tabular form, while Figure 1 shows the results in a spider graph. The major differences are the overall rating and the astringency. B#160 had a significantly (with a 95% higher confidence) higher astringency and lower rating, while the other difference fell within the error of the experiment. B#171 was very well received by the taste panel who reported its astringency as barely recognizable.

The ratings for the caramel/roasted character are interesting if you consider the starting and final gravities of each batch. B#171 counter-intuitively rated higher in both caramel and roasted than B#160 in spire of a lower final gravity. This result might be attributed to the astringency of B#160 masking the caramel/roasted character of the beer.

Figure 1 - Spider graph of survey results
The other differences between the two batches were in the carbonation and the bitterness. The carbonation is reflected in the volumes of CO2 in the beer at the time of packaging. Bitterness is easily mistaken for astringency. This may explain why B#171 was rated as having less bitterness, in spite of having the same hop bill.

Conclusions and Take-away

This experiment shows that a 0.2 difference in the mash pH can lead to astringency that will be a detriment to a beer's flavor.

There are several options available to homebrewers for adjusting the mash pH. Using food grade phosphoric acid isn't an option, as it can only be purchased in gallons (enough for tens of thousands of gallons of beer). The most economical is to add 1-2% by weight acidified malt. This malt is coated in lactic acid, which will bring the pH of your mash down. However at high concentrations, the lactic acid can lead to off flavors. I've heard that many homebrew stores sell a buffer solution that you can add to your mash, but I have no experience with them.

This experiment highlights the importance of monitoring the pH of the mash to ensure it is in the range of 5.3 to 5.8. Litmus paper can be used to get an idea of the pH, but is no substitution for a digital meter. If you are serious about making good beer, a digital pH meter should be a priority investment. They are relatively cheap from amazon, and can cost less than a batch of beer.


NOTE:I am an amazon affiliate, and will only recommend products I have experience with. Below is the most reliable pH meter, as long as you take proper care of it.

Sunday, May 11, 2014

Demystifying the mash

Figure 1 - Enzymatic activities Obtained from How to Brew
The most important part of the hot side of brewing a beer is the mash. This is the stage in the brewing process where modified barley is converted to simple sugars that the yeast can metabolize. The modification process, which mostly takes place before the barley reaches the brewer, converts the bulk of the volume of the kernel to proteins and starches. There are several different classes of enzymes (which is a type of protein) that act on the proteins and starches that contribute to the quality of the finished product. The temperature as well as the pH play a role in determining which enzyme is active in the mash. Figure 1 shows several major classes that change the chemical make up and physical properties of the mash.

Step 1 - Acid Rest - 97 degrees Fahrenheit

If the pH and temperature become too high, the husks of the grain start of leech compounds that give the beer an astringent flavor. Luckily, there exists an enzyme in grain that reduces the pH of the mash that is active around 97 degrees Fahrenheit, where the first rest lies.

The modified barley is crushed up and added to a pot of water such that it has a consistency slightly more watery than grits. In antiquity, the mash would be heated to 97 degrees and let rest for up to 2 hours while the acid-producing enzymes (phytase) lower the pH. With a modern understanding of chemistry, different salts can be added to the mash to obtain the same effect. For this reason, the acid rest is rarely used in modern breweries.

Step 2 - Protein Rest - 122-133 degrees Fahrenheit

At each step of the mash a portion of the mash is pulled off, boiled, and then mixed back with the rest of the mash. This process, called a decoction mash, does two things for the to-be beer. It increases the temperature of the mash to the next rest temperature, while also breaking down the cell walls that were not broken up during the modification process. Most breweries have a steam controlled system that closely monitors the temperature in lieu of the decoction process.

So once the first decoction is complete, your mash will be between 122 and 133 degrees. At this temperature, the enzymes important in the acid rest have been denatured (become unwound) and are nonfunctioning. This rest actives three new classes of proteins: beta-glucanase, proteases, and peptidases. Now would be a good time to mention that whenever an enzyme is responsible for breaking down a different molecule, it has the suffix -ase.

Beta-glucanase and peptidases have a positive effect on the beer. Beta-glucanase breaks down a polysaccharide called beta-glucan. Beta-glucan causes the mash to have a high viscosity which can cause problems later during the brewing process. Peptidases release free amino nitrogen (FAN), an essential yeast nutrient, into the mash. The peptidases is particularly important if the malt was under-modified and has the bulk of its nitrogen bound in large proteins instead of free amino acids.

Proteases act to ruin the quality of the beer. This is responsible for breaking down the larger proteins, which are essential to a good beer. The larger proteins (along with the unconverted starch) are responsible for the perception of body. If there are to proteins in the finished beer, it will taste thin and watery. The large proteins are also responsible for the thick foamy head and its stability. A beer with low protein content will form a weak head that will dissipate quickly. It is because of this class of protein that the timing on this rest is so important: if too much time is spent on this rest the preteases will destroy all of your proteins.

Step 3 - Saccrification Rest - 145-160 degrees Fahrenheit

This is what we've been working towards. There are two enzymes responsible for breaking down the starches into sugars: Alpha- and Beta- amylase, which are together referred to as diastatic enzymes. During the protein rest, these enzymes become soluble and go into solution where they can act on dissolved starches. These two enzymes break down the starches in different ways.

For sake of this, consider starch as a very large shrub. These two enzymes attack the shrub from two different points. The alpha-amylase is able to take off entire branches, while the beta-amylase can only sever individual twigs. Chemically speaking, the beta-amylase can only liberate glucose and maltose, while the alpha-amylase is able to liberate amylopectin, which are branched chains of glucose and maltose. Once the amylopectic "branches" have been liberated, more regions are available for the beta-amylase to free glucose and maltose (maltose is just the glucose dimer). In this way, the two enzymes work together to break apart the starch molecules.

However, they aren't the perfect team. Beta-amylase denatures before alpha-amylase. Beta-amylase is most active in between 135 and 150 degrees Fahrenheit, while alpha-amylase is most active between 150 and 160 degrees F. This disparity in optimal temperatures provides an important variable in determining the fementability of the wort. If a  low temperature is used where both enzymes are active, the starch will be largely converted to simple sugars. These will all be fermented out into alcohol and leave a thin, dry beer with a higher alcohol content. However if a higher temperature is used, the beta-amylase becomes denatured, and only the alpha-amylase acts on the starches, which leaves a portion of the starch unconverted. This means the beer will have more body, be sweeter, but have a lower alcohol content.

Apart from ingredients, the mash temperature at the saccrification rest is among the biggest factors in controlling the end product. The difference of 5 degrees can mean the difference between a malty beer that has 5% sugar by weight after fermentation and a dry beer that has barely 2% sugar by weight.

Mashing out and sparging

Once the saccrification rest is complete, the temperature of the mash is then increased to about 168 degrees F. This denatures all amylase proteins and prevents any additional conversation from taking place. At this point, the liquid containing all the sugar must be separated from the grain prior to boiling. This occurs in a process called lautering.

The mash is then strained and the wort collected. Because the grain particles are saturated with the sugary wort, hot water is rinsed through the grain to try to extract as much of the sugar as possible. The first runnings from the mash are typically between 16 and 25 percent sugar by weight, depending on the style. As the grain is rinsed with pure water this sugar concentration drops until about 3 percent. If you continue to run off after the sugar concentration drops below this point, you risk introducing harsh flavors from tannins.

Once the wort is isolated from the grain in the mash, the wort is boiled and hops are added. This boiling not only drives off different compounds from the malt that would normally lead to off flavors (mainly DMS), but also activates different flavors from the hops depending on how long they are exposed to the heat of the boil. As a hop is boiled, it first loses its aroma compounds, next its flavor compounds, then finally the alpha-acids are isomerized into compounds that are perceived as bitter.




Way more information on decoction mashes can be found here courtesy of homebrewtalk